The car came in with a large leak at the upper radiator hose. The hose was replaced and found the system could hold pressure. The block test confirmed no hydrocarbons were present in the cooling system, allowing us to continue with the recommended cooling system repairs given last visit.
FAN CLUTCH – Remove & Replace
THERMOSTAT HOUSING – Remove & Replace
RADIATOR HOSE – Remove & Replace – One,Upper or Lower
RADIATOR HOSE – Remove & Replace – Each Additional
RADIATOR RESERVE TANK – Remove & Replace
COOLING SYSTEM – Flush & Bleed (Includes: Road Test)
Hazardous Waste Disposal Fee
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
JUDY R. gave our service a 5 star review on 7/7/2024
The fan appears to be weak and is not functioning correctly. Based on a visual inspection and the overall aged appearance of the components, the following recommendations are made: 1. Replace the fan clutch to ensure proper fan operation. 2. Replace the thermostat to maintain correct engine temperature. 3. Replace all radiator hoses as a preventative measure against leaks or bursts. 4. Replace the coolant reservoir with a new sensor to ensure accurate coolant level monitoring. 5. Conduct a thorough retest to check for any potential radiator leaks, as the radiator is not clearly visible due to obstructions and the presence of dry coolant stains around the area. Note: Although the coolant did not leak under pressure testing, the replacement recommendations are based on the visual assessment and the apparent aged condition of the cooling system components, indicating that they may not be functioning effectively. Customer declined repairs at this time
AIR CLEANER ELEMENT – Remove & Replace – All Applicable Models
CABIN AIR FILTER – Remove & Replace – All Applicable Models
Road test for power steering operation. Inspect system for leaks. Flush power steering lines, pump, rack and pinion, and or gear box. Install new power steering fluid. Install power steering additive to revitalize seals. Road test vehicle.
Hazardous Waste Disposal Fee
Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
Hazardous Waste Disposal Fee
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
JUDY R. gave our service a 5 star review on 4/13/2024
TECHNICIAN INSPECTED VEHICLE AND FOUND FAULTS PRESENT FOR TIMING CORRELATION. TIMING CHAINS ARE LIKELY STRETCHED, BUT WILL NEED TO BE VERIFIED BY BMW FOR REPAIR/WARRANTY REPLACEMENT.
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
JOHN & CARRIE D. gave our service a 5 star review on 6/19/2022
Includes : Change oil and oil filter. Lube all fittings on steering linkage, ball joints & drive shaft(s). Check and correct all fluid levels to include power steering fluid, coolant, battery acid (unless battery sealed), automatic transmission fluid. Inspect brake fluid. Check tire pressure. Install "Next Service Due" sticker.
Hazardous Waste Disposal Fee
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
PAM A. gave our service a 5 star review on 4/21/2022
Includes : Change oil and oil filter. Lube all fittings on steering linkage, ball joints & drive shaft(s). Check and correct all fluid levels to include power steering fluid, coolant, battery acid (unless battery sealed), automatic transmission fluid. Inspect brake fluid. Check tire pressure. Install "Next Service Due" sticker.
Hazardous Waste Disposal Fee
VALVE COVER GASKET – Remove & Replace
FRONT BRAKE SERVICE
REAR BRAKE SERVICE
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
TULI A. gave our service a 5 star review on 10/19/2021
Includes : Change oil and oil filter. Lube all fittings on steering linkage, ball joints & drive shaft(s). Check and correct all fluid levels to include power steering fluid, coolant, battery acid (unless battery sealed), automatic transmission fluid. Inspect brake fluid. Check tire pressure. Install "Next Service Due" sticker.
Hazardous Waste Disposal Fee
Hazardous Waste Disposal Fee
Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
HEADLAMP BULB – Remove & Replace – Halogen, Driver's Side
WHEEL LOCK REMOVAL – Service
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
MELISSA O. gave our service a 5 star review on 9/24/2021
Includes : Change oil and oil filter. Lube all fittings on steering linkage, ball joints & drive shaft(s). Check and correct all fluid levels to include power steering fluid, coolant, battery acid (unless battery sealed), automatic transmission fluid. Inspect brake fluid. Check tire pressure. Install "Next Service Due" sticker.
Hazardous Waste Disposal Fee
SET TIRE PRESSURES TO MANUFACTURER SPECIFICATION
DEBY S. gave our service a 5 star review on 9/22/2021